Grain Mill

Thank you for using stainless steel grain Cereal Mill! In order to give full play to device performance, please read carefully before you use this manual.
I. Technical parameters

II. Milling machine operation and adjustment.

1. Open the front cover, will be moving grinding, springs,top shaft,bearings,etc. Installed.
2. The hopper into the feed port into the shell cover. In the milling,the feed should be noted that Volume, adjust flapper, so as not to feed too fast, stuck motor.
3.In order to prevent static grinding rotation, loosening, apply screw fixed to the milling of its cavity.

1. Milling, the materials required to dry, wet material may not be used, otherwise will stick to grinding ,not material.

5. Grinding the working space must be based on the thickness of the material needed to adjust when you first release the adjustment nut, thickness by adjustment screws to adjust properly,it will tighten the adjustment nut.
6. Dynamic adjustment of grinding, remove the moving grinding, grinding on the release of three screws, remove the spring, will move back to even-axis grinding equipment, and then adjust grinding, grinding until it coincides with the static grinding disc.

III. Notes

1. Each pre-boot, should check Grinding, action
Grinding and into the grinding hopper fastening screw is loosened,and tighten them.
2. By the end of each machine should be clean inside the machine,and ventilation Dry.
3. Machine parts found to have serious wear and tear or damage should be promptly repaired or replaced.
4. Longer period of time the machine when not in use, the machine not to inverted, please horizontally,and cut off the power.
5.The level of the machine should be installed.in the table.
6. The machine starts, it should be running only when the normal discharge process, pay attention to fluxes card readers to prevent motor overload.
7. During processing, such as a sudden shutdown because of power failures and other reasons, must be removed in order to restart the  milling chamber materials.
8. Processed grain cereals, Chinese herbal medicine when the need to dry, remove stones, metal and other debris.
9.In strict accordance with the provisions ground line, the motor should be to counter clockwise turn, the normal operation of the machine is the same as always, before operation processing material.
Four. method of operation

A. operation methods

1. The machine before use every day to check whether the machine running normal, static abrasive disc and dynamic abrasive disc of whether there is a screw loose, and to screw up.
2, grinding dry material
Grinding dry material need grinding twice,first coarse grinding, the second fine grinding.
The first rough grinding, regulating adjusting screw to abrasive disc has a slight sound friction voice, again to coarse back to adjust to just not grating, and then open the feed opening plug edition 1/2 — can be a third.
The second fine grinding, regulating adjusting screw to abrasive disc has a slight sound friction voice, again to fine adjustment adjusting screw 1/6—1/4 turn, (according to the fineness of grinding requirements a control) abrasive disc have ear-piercing sound grating and then open the feed opening plug edition 1/2 — can be a third.
3, grinding dry and oily mixed material
Method 1
Grinding dry and oily mixed material need grinding twice, first coarse grinding, the second fine grinding.
The first rough grinding, regulating
adjusting screw to abrasive disc just has a slight sound friction voice, again to coarse back to control adjusting screw a circle, and then completely open the feed opening board can; (grind materials almost half of the size of a grain of rice).
The second fine grinding, regulating
adjusting screw to abrasive disc just has a slight sound friction voice to open the feed opening board 1/4 — can be a third.
Method 2
The first will dry material mill (and ground dry material operation method).
The second will have been grinding good dry material and oily materials mixing, and then control adjusting screw to abrasive disc just has a slight sound friction voice, then open the feed opening board 1/4 — can be a third.
4. grinding contain sugar high material Grinding contain sugar high material, (for
example, red jujube, kumquat tablet,Chinese wolf berry, etc.) sugar high material must baking dry, water, or frozen two hours to grinding, only need to grind a, regulate the adjusting screw to abrasive disc just Have a slight sound friction
voice, then open the feed opening board can, (separate grinding carrot tablet need
grinding twice,first coarse grinding and grinding dry material, first coarse grinding operation, the second fine grinding regulation adjusting screw to abrasive disc just have sound of friction voice, then open the feed opening board 1/4 — can be a third).
5. grinding contain sugar high mixing materials, operating method and ground dry
and oily mixed materials same operation method.

Second, change abrasive disc

1.. remove the old mill tablet (abrasive disc have positive and negative, the static abrasive disc and dynamic abrasive disc can
exchange use).
2. installed abrasive disc, adjust the abrasive disc inner hole and crushing set or dynamic millstones installation_position of the gap even to tighten the screws.
3, regulating abrasive disc flat: open machine, regulate the adjusting screw to polish a harsh voice, run 20-30 seconds, stop open the front end cover, take out abrasive disc, with the hand gently touch static abrasive disc around feel which position temperature high or low temperature, high temperature position description abrasive disc high, low temperature position description abrasive disc low,（or see
abrasive disc which position tooth light or no ground light, the position of the light that high, not the position of the light that low.)
 
The location of the high fixed abrasive disc screw tightening, low position fixed abrasive disc of the screw loose a bit, and open machines repeat the operation until the abrasive disc regulation level off, the lock screw.
Three, running in abrasive disc

1, take two or three catties rice into the funnel, start machine control adjusting screw to abrasive disc just has a slight sound.
Friction voice, again to fine adjustment adjusting screw a third-two-thirds cirele,
abrasive disc have ear-piercing sound grating, open the feed opening plug edition 1/2-a third, repeat the grinding out of the rice flour rewind funnel grinding 15-20 minutes, and then take 2 two or so rice according to grinding dry material method operation, try a grinding out rice meets the fineness requirement.
If did not reach the fineness requirement repeat the above operation.
 
VI, Common Faults and exclusion method

Wearing parts: moving grinding disc.